[CP2K-user] [CP2K:18267] Re: Help for 2nd order CPMD

[Moon Moon]

Dear lannuzzi

Thank you for careful comments on SGCP settings.
As you said, the accuracy of the SGCP should be determined by comparing 
with BO values at the same coordinates.
But even among BO simulations with different parameters, the lines of 
energy and forces may change.
So how can I compare SGCP values with BO values ?

Moon

在2022年11月27日星期日 UTC+9 18:46:45<Marcella Iannuzzi> 写道：

> Dear Dmitrii
>
> The parameters are determined by testing. 
> One has to find the conditions for which the  noise term generates the 
> correct average temperature, as measured by the equipartition theorem.
> This leads to the correct sampling. 
> Gamma should be small, as long as the error in the forces is small. Under 
> these conditions the dynamical properties are  correct.   
> The first term of comparison to determine the accuracy of the SGCP 
> description is obtained from the deviations in  energy  and  forces  with 
>  respect  to  the  BO  values  at the same coordinates.
> The force deviation has to have a vanishing average, and also that the 
> distribution of errors should be Gaussian.
>
> Regards
> Marcella
>
> On Sunday, November 27, 2022 at 3:19:47 AM UTC+1 dresear... at gmail.com 
> wrote:
>
>>
>> Dear CP2k community,
>>
>> I am trying to run the 2nd order CPMD. I have ionic liquid system in NVT 
>> ensemble. 
>> Could you please advice how to select GAMMA and NOISY_GAMMA?
>>
>> Also in this section below.
>>
>> &MOTION
>>   &MD
>>     ENSEMBLE LANGEVIN
>>     ...
>>     &LANGEVIN
>>       GAMMA 0.001
>>     &END LANGEVIN
>>     ...
>>   &END MD
>>
>>
>> I have my BOMD script below.
>>
>> Many thanks,
>> Dmitrii
>>
>>
>>
>> &FORCE_EVAL
>>   METHOD QS
>>   &DFT
>>     BASIS_SET_FILE_NAME BASIS_MOLOPT
>>     POTENTIAL_FILE_NAME GTH_POTENTIALS
>>     CHARGE 0
>>     MULTIPLICITY 1
>>     &MGRID
>>       CUTOFF 400
>>       NGRIDS 4
>>       REL_CUTOFF 40
>>     &END MGRID
>>     &QS
>>        METHOD GAPW
>>        EPS_DEFAULT 1.0E-12
>>        EXTRAPOLATION ASPC
>>        EXTRAPOLATION_ORDER 3
>>     &END
>>     &SCF
>>       SCF_GUESS ATOMIC
>>       EPS_SCF 1.0E-6
>>       MAX_SCF 15
>>       &OT
>>        MINIMIZER DIIS
>>        PRECONDITIONER FULL_KINETIC
>>        &END OT
>>       &OUTER_SCF
>>        EPS_SCF 1.0E-6
>>        MAX_SCF 20
>>       &END
>>       &PRINT
>>        &RESTART
>>         &EACH
>>          MD 0
>>         &END EACH
>>        &END
>>       &END
>>     &END SCF
>>    
>>     &XC
>>       &XC_FUNCTIONAL BLYP
>>       &END XC_FUNCTIONAL
>>       &XC_GRID
>>        XC_DERIV NN10_SMOOTH
>>        XC_SMOOTH_RHO NN10
>>       &END XC_GRID
>>       &vdW_POTENTIAL
>>         DISPERSION_FUNCTIONAL PAIR_POTENTIAL
>>          &PAIR_POTENTIAL
>>             PARAMETER_FILE_NAME dftd3.dat
>>                TYPE DFTD3
>>                REFERENCE_FUNCTIONAL BLYP
>>         &END PAIR_POTENTIAL
>>      &END vdW_POTENTIAL
>>     &END XC
>>     &POISSON
>>       PERIODIC xyz
>>       POISSON_SOLVER PERIODIC
>>     &END POISSON
>>   &END DFT
>>   &SUBSYS
>>     &CELL
>>       ABC 19.3457 19.3457 19.3457
>>       PERIODIC xyz
>>     &END CELL
>>     &TOPOLOGY
>>       COORD_FILE_NAME npt.xyz
>>       COORD_FILE_FORMAT XYZ
>>     &END TOPOLOGY
>>     &KIND H                              
>>       BASIS_SET TZV2P-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q1            
>>     &END KIND
>>     &KIND Al
>>       BASIS_SET DZVP-MOLOPT-SR-GTH
>>       POTENTIAL GTH-BLYP-q3
>>     &END KIND
>>     &KIND F
>>       BASIS_SET TZVP-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q7
>>     &END KIND
>>     &KIND O
>>       BASIS_SET TZVP-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q6
>>     &END KIND
>>     &KIND C
>>       BASIS_SET TZVP-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q4
>>     &END KIND
>>     &KIND S
>>       BASIS_SET TZVP-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q6
>>     &END KIND
>>     &KIND N
>>       BASIS_SET TZVP-MOLOPT-GTH
>>       POTENTIAL GTH-BLYP-q5
>>     &END KIND
>>    &END SUBSYS
>> &END FORCE_EVAL
>>
>> &GLOBAL
>>   PROJECT IL_nvt
>>   RUN_TYPE MD
>>   PRINT_LEVEL LOW
>>   FFTW_PLAN_TYPE EXHAUSTIVE
>> &END GLOBAL
>> &MOTION
>>  &MD
>>   ENSEMBLE NVT
>>   STEPS 2000
>>   TIMESTEP 0.5
>>   &THERMOSTAT
>>    TYPE NOSE
>>    REGION MASSIVE
>>    &NOSE
>>     TIMECON 10.00
>>    &END NOSE
>>   &END THERMOSTAT
>>   TEMPERATURE 303
>>  &END MD
>>   &PRINT
>>    &TRAJECTORY
>>      &EACH
>>        MD 1
>>      &END EACH
>>    &END TRAJECTORY
>>    &VELOCITIES OFF
>>    &END VELOCITIES
>>    &FORCES OFF
>>    &END FORCES
>>    &RESTART_HISTORY
>>      &EACH
>>        MD 500
>>      &END EACH
>>    &END RESTART_HISTORY
>>    &RESTART
>>      BACKUP_COPIES 3
>>      &EACH
>>        MD 1
>>      &END EACH
>>    &END RESTART
>>   &END PRINT
>> &END
>> &EXT_RESTART
>>   RESTART_FILE_NAME nvt-1.restart
>> &END
>>
>> --
>> You received this message because you are subscribed to a topic in the 
>> Google Groups "cp2k" group.
>> To unsubscribe from this topic, visit 
>> https://groups.google.com/d/topic/cp2k/dZWkRW-Frqg/unsubscribe.
>> To unsubscribe from this group and all its topics, send an email to 
>> cp2k+uns... at googlegroups.com.
>> To view this discussion on the web visit 
>> https://groups.google.com/d/msgid/cp2k/455530e4-9857-448c-b74c-eb87b966a6b8n%40googlegroups.com
>> .
>>
>>

-- 
You received this message because you are subscribed to the Google Groups "cp2k" group.
To unsubscribe from this group and stop receiving emails from it, send an email to cp2k+unsubscribe at googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/cp2k/349ca624-8f51-4b68-98e7-a9f09cc3328cn%40googlegroups.com.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.cp2k.org/archives/cp2k-user/attachments/20221229/d7da6207/attachment.htm>